Ngày cập nhật: 22/04/2025
Quy cách sản phẩm
| Type | [ M ]Material | [ H ]Hardness | [ S ]Surface Treatment | ||
| D Tol. g6 | D Tol. h5 | D Tol. f8 | |||
| SFJW | SFUW | – | SUJ2 Equivalent | Effective Hardened Depth of Induction Hardening >> P.142 SUJ2 Equivalent: 58HRC~ SUS440C or 13Cr stainless: 56HRC~ |
– |
| SSFJW | SSFUW | – | SUS440C or 13Cr stainless | ||
| PSFJW | PSFUW | – | SUJ2 Equivalent | Hard Chrome Plating – Plating Hardness: HV750 ~, Plating Thickness: 5µ or More | |
| PSSFJW | PSSFUW | – | SUS440C or 13Cr stainless | ||
| RSFJW | – | – | SUJ2 Equivalent | Low Temp. Black Chrome Plating | |
| – | – | PSFGW | S45C Equivalent | – | Hard Chrome Plating – Plating Hardness: HV750 ~, Plating Thickness: 10µ or More |
| – | – | PSSFGW | SUS304 | ||
[ ! ]Annealing may lower hardness at shaft end machined areas (effective thread length + approx. 10mm). >> P.142
[ ! ]Full Length Hardness Guaranteed Shafts p1_155
[ ! ]L Dimension Tolerance, Circularity, Straightness, Perpendicularity, Concentricity and Changes in Hardness >> P.141
[ ! ]Features of Low Temp. Black Chrome Plating p1_156
Specifications
| Part Number | – | L | – | M | – | N |
| SFJW8 SSFJW20 |
– – |
200 500 |
– – |
M4 M6 |
– – |
N4 N10 |
| Part Number | L 1mm Increments |
M (Coarse), N (Coarse) Selection | D Tol. | C | ||||||||||||||||
| Type | D | g6 | h5 | f8 | ||||||||||||||||
| (D Tol. g6) SFJW SSFJW PSFJW PSSFJW (D Tol. f8) PSFGW PSSFGW |
(D Tol. h5) SFUW SSFUW PSFUW PSSFUW |
4 | 20~ 300 | 2 | -0.004 -0.012 |
0 -0.005 |
– | 0.2 or Less | ||||||||||||
| 5 | 20~ 400 | 2.6 | 3 | -0.004 -0.012 |
0 -0.005 |
– | 0.2 or Less | |||||||||||||
| 6 | 20~ 800 | 3 | -0.004 -0.012 |
0 -0.005 |
-0.010 -0.028 |
0.5 or Less | ||||||||||||||
| 8 | 20~1000 | 3 | 4 | 5 | -0.005 -0.014 |
0 -0.006 |
-0.013 -0.035 |
0.5 or Less | ||||||||||||
| 10 | 20~1000 | 3 | 4 | 5 | 6 | -0.005 -0.014 |
0 -0.006 |
-0.013 -0.035 |
0.5 or Less | |||||||||||
| 12 | 20~1200 | 4 | 5 | 6 | 8 | -0.006 -0.017 |
0 -0.008 |
-0.016 -0.043 |
0.5 or Less | |||||||||||
| 13 | 25~1200 | 4 | 5 | 6 | 8 | -0.006 -0.017 |
0 -0.008 |
-0.016 -0.043 |
0.5 or Less | |||||||||||
| 15 | 25~1200 | 4 | 5 | 6 | 8 | 10 | -0.006 -0.017 |
0 -0.008 |
-0.016 -0.043 |
0.5 or Less | ||||||||||
| 16 | 30~1200 | 4 | 5 | 6 | 8 | 10 | -0.006 -0.017 |
0 -0.008 |
-0.016 -0.043 |
0.5 or Less | ||||||||||
| 18 | 30~1200 | 4 | 5 | 6 | 8 | 10 | 12 | -0.006 -0.017 |
0 -0.008 |
-0.016 -0.043 |
0.5 or Less | |||||||||
| 20 | 30~1200 | 4 | 5 | 6 | 8 | 10 | 12 | -0.007 -0.020 |
0 -0.009 |
-0.020 -0.053 |
1.0 or Less | |||||||||
| 25 | 35~1200 | 4 | 5 | 6 | 8 | 10 | 12 | 16 | -0.007 -0.020 |
0 -0.009 |
-0.020 -0.053 |
1.0 or Less | ||||||||
| 30 | 35~1500 | 6 | 8 | 10 | 12 | 16 | 20 | -0.007 -0.020 |
0 -0.009 |
-0.020 -0.053 |
1.0 or Less | |||||||||
| 35 | 35~1500 | 8 | 10 | 12 | 16 | 20 | 24 | -0.009 -0.025 |
0 -0.011 |
-0.025 -0.064 |
1.0 or Less | |||||||||
| 40 | 50~1500 | 10 | 12 | 16 | 20 | 24 | 30 | -0.009 -0.025 |
0 -0.011 |
-0.025 -0.064 |
1.0 or Less | |||||||||
| 50 | 65~1500 | 12 | 16 | 20 | 24 | 30 | -0.009 -0.025 |
0 -0.011 |
-0.025 -0.064 |
1.0 or Less | ||||||||||
| Part Number | L 1mm Increments |
M (Coarse), N (Coarse) Selection |
D Tol. | C | |||||||||||
| Type | D | g6 | |||||||||||||
| (D Tol. g6) Low Temp. Black Chrome Plating |
4 | 20~300 | 2 | -0.004 -0.012 |
0.2 or Less | ||||||||||
| 5 | 20~400 | 2.6 | 3 | -0.004 -0.012 |
0.2 or Less | ||||||||||
| 6 | 20~500 | 3 | -0.004 -0.012 |
0.5 or Less | |||||||||||
| 8 | 20~500 | 3 | 4 | 5 | -0.005 -0.014 |
0.5 or Less | |||||||||
| 10 | 20~500 | 3 | 4 | 5 | 6 | -0.005 -0.014 |
0.5 or Less | ||||||||
| 12 | 20~500 | 4 | 5 | 6 | 8 | -0.006 -0.017 |
0.5 or Less | ||||||||
| 13 | 25~500 | 4 | 5 | 6 | 8 | -0.006 -0.017 |
0.5 or Less | ||||||||
| 15 | 25~500 | 4 | 5 | 6 | 8 | 10 | -0.006 -0.017 |
0.5 or Less | |||||||
| 16 | 30~500 | 4 | 5 | 6 | 8 | 10 | -0.006 -0.017 |
0.5 or Less | |||||||
| 18 | 30~500 | 4 | 5 | 6 | 8 | 10 | 12 | -0.006 -0.017 |
0.5 or Less | ||||||
| 20 | 30~500 | 4 | 5 | 6 | 8 | 10 | 12 | -0.007 -0.020 |
1.0 or Less | ||||||
| 25 | 35~500 | 4 | 5 | 6 | 8 | 10 | 12 | 16 | -0.007 -0.020 |
1.0 or Less | |||||
| 30 | 35~500 | 6 | 8 | 10 | 12 | 16 | 20 | -0.007 -0.020 |
1.0 or Less | ||||||
[ ! ]L requires Mx2+Nx2≤L. [ ! ]When Mx2.5+4+Nx2.5+4≥L, tap pilot holes may go through and the effective length of the smaller tap part may be shortened.
Alterations
Thông tin thêm
Chính sách vận chuyển
Chưa có thông tin chính sách vận chuyển cho sản phẩm này.
Đánh giá
Đánh giá
Chưa có đánh giá nào.